OVERVIEW

• Model: MVR-210 (5ch GPS Mobile DVR)
• Functionality: Preview, Record, Playback, Locate

SYSTEM

• O/S: Linux 3.0.8
• Control Mode: Mouse, Easy Check, CP4

VIDEO

• Input: 4 channels WD1 + 1 channel 720P
• Output: 1 channel
• Total Resource: 100/120fps @ WD1 + 30fps @ 720P IPC
• Video Signal Standard: Electrical level: 1Vpp, Impedance : 75Ω NTSC/PAL Optional

AUDIO

• Input: 5 channels (incl. 1 channel IPC audio input)
• Output: 1 channel
• Audio Signal Standard: Electrical level: 2Vpp, Input impedance: 4.7kΩ

DISPLAY

• Display Split: 1/4/9
• OSD: GPS information, alarm, vehicle number, speed, date/time
• Operation: Graphical User Interface (semi-transparent)

RECORDING

• Video/Audio Compression: Video (H.264), Audio (ADPCM)
• Image Resolution
  • Analog: PAL: WD1 (928x576), WHD1 (928x288), WCIF (464x288), D1 (704x576), HD1 (704x288), CIF (352x288) ; NTSC: WD1 (928x480), WHD1 (928x240), WCIF (464x240), D1 (704x480), HD1 (704x240), CIF (352x240)
  • Digital: 720P (1280x720)
• Image Quality: 1~8 levels adjustable (1 is the best)
• Record Mode: Boot up/Manual/schedule/Alarm
• Pre-recording: 0~60 minutes
• Post-recording: 0~30 minutes
• Mirror/Dual Record: Support

PLAYBACK

• Playback Channel: 1 channel by local playback
• Search Mode: Date/time, channel, event

ETHERNET

• IPC Ethernet: 6-pin DJ (100M x 1, PON power supply)

LOCATING

• GPS: Location tracking, speed detection and sync time

STORAGE

• SD Card: SD Card x 2 (total 256GB capacity)

INTERFACE

• USB: USB 2.0 x1
• RS232: RS232 x 1
• Sensor: 8 inputs / 2 outputs
• Speed: 1 channel pulse speed detection
• Intercommunication: 1 MIC interface

 ELECTRICAL

• Input: DC8~36V, ignition signal
• Output: 5V@500mA
• Power Consumption: 29W (Maxi.) ; ≈0W (Standby)

MECHANICAL

• Ingress Protection: IP54
• Dimension (WxDxH): 167.3x146.3x 54.1(mm)/ 6.58”x5.76”x2.13”
• Weight: 0.83kg / 1.83lbs

ENVIRONMENTAL

• Operating Temperature: 
  • -40℃~+70℃ / -40℉~158℉ (with heater)
  • -10℃~+70℃ / -14℉~158℉
• Operating Relative Humidity: 8% ~ 90% (No Condense)

PC SOFTWARE

• VMS 2.0

CERTIFICATION

• EU: CE, USA: FCC

ACCESSORY

• Standard: Remote Control*1, Vehicle Fuses (7.5A & 15A)*2, Screw*6, 9pin aviation power input wire*1, MDVR key*1

Note:

1. MVR-210A is an economic MDVR which does not support 3G/4G or WIFI function.
2. Data is subject to change without prior notice.

Dimension (mm)

Rear Panel

The system can’t start? 

This problem usually results from the incorrect power connection. Please follow below steps to check the power connection: 

1. Check the input power, whether the power wire is connected correctly, whether the ground wire is connected back to the battery, and whether the fuse on the power wire is in good condition.
2. Check whether the ACC signal wire input to the power is with voltage higher than 7V.
3. Check whether the device key is closed.

The MDVR restarts uninterruptedly? 

Please follow below steps to check it: 

1. Check whether the voltage of MDVR is insufficient. If the voltage is less than the start-up voltage of the device, the device would always restart.
2. The problem in hard disk/SD card may cause the failure to start. Take off the storage part and check whether it is broken down.

The device can’t record?

This problem usually results from the storage disk or camera. Please follow below steps to check it: 

1. Check whether the storage disk is installed, whether it is in good contact, and whether the disk can be read normally in computer.
2. Check whether the storage disk is formatted. The storage disk should be formatted before normally storing record files.
3. Check whether there is video signal input into the device from camera, and whether there is video/image on the screen.

There is no voice in record file?

Please follow below steps to check it: 

1. Check whether there is an external pickup, or whether the camera features with the function of audio collection.
2. Access to Video Channel Settings, check if Audio is set on.
3. There must be video input into the channel for recording and it must record normally.

The GPS works abnormally? 

Please follow below steps to check it:

1. Check whether the GPS antenna is installed correctly. There is a silk print logo on the GPS antenna holder behind the host device.
2. Check whether the antenna receiver is sheltered. It should not be covered by any stuff, which may cause it not to receive signals.
3. Environmental influence such as tree shades, being inside tunnel, driving near tall building or elevated roads, thunderstorms or other weather influence, etc. can also cause signal loss or receiving wrong signals.

The device can’t shutdown in ignition switch mode?

Please follow below steps to check it: 

1. Check if the ACC line connection mode is correct; and check whether there is voltage on ACC yellow line when the key is turned off.
2. If the device has been set with schedule recording, it can’t shutdown if it is still during recording time of the task table.